I’ve highlighted the topic of plant turnarounds (planned downtime for maintenance) a few times in the past. Back from the Emerson Exchange, here’s my take on the Smart Turnaround workshop. For continuous processes that run for years, this turnaround provides opportunity to update, fix, repair, and replace a host of plant assets including instruments, valves, electrical distribution equipment, connectors and cabling, and the overall performance of the process.
The Emerson presenters looked at the advanced planning that can be done from these various perspectives. From these diverse areas of expertise, diagnostic testing helps develop a turnaround plan that prioritizes critical asset work, defines the scope of work, develops the schedule for the work, and identifies the parts and people required to best get this difficult work done.
Chris Forland an operations consultant whose work I’ve highlighted in earlier posts kicked off the session discussing some of the challenges of the turnaround process. A big one is finding problems you didn’t expect while in the turnaround. These unexpected problems cause extra charges and delays. Chris discussed ways that Emerson turnaround specialists can help with the detailed planning to make sure the work is efficiently performed during the turnaround. He noted that less time to plan mean less flexibility as the turnaround date approaches. Other challenges included maintaining compliance with safety and regulatory compliance, working with budget constraints, reducing process variability, losing experienced personnel due to infrequency of turnarounds, and pressuring of short turnarounds due to sold out condition of produced product.
Scott Grunwald, a turnaround business manager in the Instrument & Valve Services business, recommended that with the valves and instruments, you start by building the plan based on the benefits to be achieved the roles of all participants in the maintenance activities, and the prioritized list of activities and anticipated timelines. The process starts with a walk down of the facility. Next, FlowScanner is used to measure internal valve conditions to identify problems to address during the turnaround. When it’s time for executing the turnaround, only valves needing significant work are removed. Other valves are repaired in place.
The team often brings an on-sight mobile trailer that is a self-contained workshop to rework the instrument and valves right on-site. This helps to expedite the repair process.
Looking at turnarounds from an electrical reliability perspective, Steve Metzger described the goal–to prioritize and focus the resources by pre-diagnosing troubleshooting, followed by the planning of the repair services and parts required to get the lead times properly. The key is to do as much pre-work as possible, fix what’s possible, and remove it from the scope of the turnaround to lessen the pile of work to be done.
On-line partial discharge testing before the turnaround detects cables with degrading insulation that could cause short circuits and unexpected downtime. This testing helps determine which cables are OK and which need to be replaced during the turnaround.
James Beall, also highlighted in earlier posts, summed up the goal of a Smart Turnaround–to identify the items you can fix in advance, and prioritize what can’t be in the turnaround plan. James and the variability management consultants look at the control performance and opportunities to reduce process variability through better tuning. James gave an example of a mixing temperature control loop where the deadtime was nine minutes between a change in setpoint and response the temperature was changing. The problem was not in the loop tuning but rather in the lag caused by the temperature transmitter being located 250 feet from where it should have been. Finding this early in the process allowed this installation mistake to be scheduled and fixed during the turnaround.
Chris closed this presentation with how you can look at the return on investment to help justify the experts required to make the planning and execution of the turnaround a success. It’s a bit of a chicken and egg scenario since you don’t know what type of ROI this turnaround planning can create without having the experts come in to begin the process of identifying improvement opportunities.
Chris has developed a model based on turnaround experience with typical costs from each of the aspects of turnaround planning and typical costs for the maintenance activities. This model is in an excel spreadsheets so that the assumptions can be easily changed to fit the unique aspects of each process manufacturer. Both cost avoidance and increased revenue from improved plant performance is calculated, each based on the size of the process and amount of equipment considered.
By taking a comprehensive planning approach, and getting an early start, turnarounds do not have to cause quite the number of gray hairs that they have traditionally been known to cause.
Update: Mitzi Amon, director of marketing for Emerson Electrical Reliability Services team adds that the prioritization is accomplished by performing online diagnostic testing prior to the turnaround to determine what electrical equipment needs to be serviced during the turnaround. This helps clearly define maintenance work scope during the turnaround and what can be done prior to the the turnaround.
